Why we do Layout Inspection of any product?

Dilip

• Aug 22nd, 2017

To efficiently utilize space without any wastage.

Kapil

• May 28th, 2017

We do layout inspection to ensure our product is as per customer requirement or not.

Answer Question  Select Best Answer

What are the Efficiency of Gas, Steam, Hydro Turbines?

Prakash

• Jul 30th, 2016

Eiff =OP/IP

abdullah

• Jun 13th, 2016

(Q out - Q in)/Q in
the efficiency is the ratio between what we got over what we give. at any thing

Answer Question  Select Best Answer

Explain What are the 7QC tools?

victor

• Nov 1st, 2017

Cause-and-effect diagram (also known as the "fishbone" or Ishikawa diagram)
Check sheet.
Control chart.
Histogram.
Pareto chart.
Scatter diagram.
Stratification (alternately, flow chart or run chart)

Felix

• Jul 21st, 2016

Check sheet
Histogram
Control chart
Paretto diagram
Cause and effect diag
Scatter diag
Flow chart

Answer Question  Select Best Answer

Which type of heat exchangers are commonly used:
a. Counter current flow
b. Parrell current flow
c. Cross flow
d. All the above

Aitazaz

• Aug 8th, 2017

Counter current is mainly used in refineries to increase heat exchange but if we will talk about industrial scale like cooling towers then cross flow has the major importance.

Lalith

• Apr 9th, 2017

Counter Flow H.E. are mostly used. Because:
1. More heat exchange, with minimum medium of exchanger.
2. Less material requirement for production.
3. Can be utilized for small exchange purpose to High as required.

Answer Question  Select Best Answer

manjunath

• Jul 18th, 2011

If air is used for power transmission or generation then it is called pneumatic engine

Sudharshan Ganesh

 Profile Answers by Sudharshan Ganesh Questions by Sudharshan Ganesh

• Jul 9th, 2011

I am not sure about this. may be it is the engine that runs on compressed gas..there is one vehicle called as air pod that runs on compressed gas.

Answer Question  Select Best Answer

What is the function of jokey pump?

kit_inton

 Profile Answers by kit_inton Questions by kit_inton

• Jun 19th, 2011

The? function of jokey pump is to maintain the pressure in pipe line,?pressure switch set at hi/lo?to start the jokey?pump motor, in case the pressure drop that jokey pump can't build up the pressure, then the main pump automatically start.

vasujoshi123

 Profile Answers by vasujoshi123 Questions by vasujoshi123

• Feb 11th, 2009

Jockey pump is working to keep fire hydrant system in pressurised condition always.If any pressure decreases in the system, automatically hydrant pump starts immediately to cope up the required pressure or supplying the required water to the required area.

Answer Question  Select Best Answer

rameez.ajmeri

 Profile Answers by rameez.ajmeri Questions by rameez.ajmeri

• Jan 13th, 2012

Hello sargkuna, I would like to correct your answer. In fact there are two reasons, the form factor of power generating alternator is 1.11 due to which the transmission voltage is made in multiples ...

sargkuna

• Jul 26th, 2011

The reason is some thing historical. In olden days when the electricity becomes popular, the people had a misconception that in the transmission line there would be a voltage loss of around 10%. So in...

Answer Question  Select Best Answer

jitesh kumar

• Nov 11th, 2006

Hi sir/mam i need Group discussion topics and interview questions to beat the BPCL's interview thanks

Answer Question  Select Best Answer

sandipg22

 Profile Answers by sandipg22 Questions by sandipg22

• Nov 30th, 2008

There are two test, one is general inteligence test.In this test 40 questions you have to answer in 15 minall are objective types question , minimum passing is 24 marks.1 mark per correct answer quest...

Answer Question  Select Best Answer

bhargavmech

 Profile Answers by bhargavmech Questions by bhargavmech

• Aug 27th, 2009

Hey i got the halticket for the vizag steel re-test.. halticket is nw given for only for those candidates who already had written the earlier exam...Now the exam is on 6th of sept (3PM-5PM)

Answer Question  Select Best Answer

shranik_2005

 Profile Answers by shranik_2005 Questions by shranik_2005

• Apr 30th, 2009

There are two answer for this1) Follow the steps Switch on the, MCB, stabiliser, main switch, emergency switch then first give reff to Z axis .To start the prg where it was stopped first call the prog...

Answer Question  Select Best Answer

Kumaran J

• Sep 4th, 2007

Theoretically spherical vessel is more reliable than cylindrical. But construction is more complicated than cylindrical. In spherical vessel stress distribution is uniform throughout the vessel. This is safer than cylindrical.

Answer Question  Select Best Answer

karthicvijay

 Profile Answers by karthicvijay Questions by karthicvijay

• Apr 30th, 2010

1. Dont work hard but work smart.2. Bring out new innoviative ideas and share it with the world.3. Thinking different from others.4. Thirst for improvements.5. Always being sensitive. 

Answer Question  Select Best Answer

Usman Adil

 Profile Answers by Usman Adil Questions by Usman Adil

• Feb 3rd, 2009

Very simple, A mechanical engineering is called a mother of all the fields. So today every individual is wanting three basic properties in each product ease, economy and strength. Ease relates to auto...

Answer Question  Select Best Answer

ksreenivasan02

 Profile Answers by ksreenivasan02 Questions by ksreenivasan02

• Jan 28th, 2009

A magnetorheological damper or magnetorheological shock absorber is a damper filled with magnetorheological fluid, which is controlled by a magnetic field, usually using an electromagnet.This allows t...

Answer Question  Select Best Answer

Blank size is equal to size of punch in presswork.

prasad surendra naik

 Profile Answers by prasad surendra naik Questions by prasad surendra naik

• Oct 13th, 2008

Blank size=punch size+punch allowances

Answer Question  Select Best Answer

for uniform strength of beam condition req.A. Depth constant, width increases.B. Depth increases, width decreases.C. Both should increase.D. All the above.E. None of the above.

dostmitra_05

 Profile Answers by dostmitra_05 Questions by dostmitra_05

• Jun 27th, 2008

Cross sectional area is to be decreased towards the support. this can be achieved by:a)keeping the depth constant and varying the widthb)keeping the width constant and varying the depthc)varying both the depth & width

Answer Question  Select Best Answer

Explain about calibration method of sigma comparator optical systems ?

subrat

• Oct 9th, 2014

Sigma comparator is used to comparison between measurement of object or device...

Answer Question  Select Best Answer

Hi,Can anybody tell me few companies list which are in GIS services in Bangalore

vrsaikumar

 Profile Answers by vrsaikumar Questions by vrsaikumar

• Nov 11th, 2008

Google Inc is the biggest GIS (Geographical Information System) provider in India..There is a plenty of openings in google and also other local companies who use GIS.. I came to know that some govt or...

Answer Question  Select Best Answer

Tungsten Inert Gas welding and Megnesium Inert Gas welding is used for which material welding and what are their advantages?

dv_rjn

 Profile Answers by dv_rjn Questions by dv_rjn

• Dec 29th, 2008

Tig and Mig welding used for alloy steels and the process is cheaper, less spatters, more strength

Answer Question  Select Best Answer