Gopi

• Jun 1st, 2005

8416 - 2A16 = 5A00

Sathyagopi

• Jun 1st, 2005

8416 - 2A16 = 5A00

Answer Question  Select Best Answer

vikas s kulkarni

• Aug 3rd, 2005

Actually question is about controller ,controller first aserts intr signal  then after receiving intra continues the communication 

nanna kumar

• Jun 29th, 2005

when interrupt occur controller finish its current executing operation. It store the address of the next instruction. jump to IVT(intrrupt vector table).where add of ISR(int.service routine)...

Answer Question  Select Best Answer

Venkataramana kotakonda

• Nov 30th, 2005

Four test vector are required. To test 'struck at 0' fault  111 is the input test vector and to test 'struck at 1' fault 110 , 101 ,011 are the input test vectors.

Answer Question  Select Best Answer

vishal herode

• Dec 14th, 2005

Interrupts

vishal herode

• Dec 14th, 2005

Interrupts

Answer Question  Select Best Answer

Ramachandran P.R

• Apr 30th, 2006

PLL stands Phase Locked Loop and it consists of phasedetctor,lowpassfilter,error amplifier,voltage controlled oscillator

Answer Question  Select Best Answer

Danny John

• Aug 8th, 2006

Since Y=C'BA'+CB'A+CBA on simplification yields Y=C'BA' + CANow it depends on the multiplexer we are using. If 8:1 MUX is used then just use A, B, C as select lines and the output of the truth table a...

Answer Question  Select Best Answer

Danny John

• Aug 8th, 2006

512 adresses and 4 bit word. Hence 2048 bits.

bharti

• Jul 13th, 2006

Bytes or Bits ??

Answer Question  Select Best Answer

Danny John

• Aug 8th, 2006

I think the output remains the same because it violates both setup time and hold time that is the input should remain constant for the setup time before the clock pulse and constant for the hold time after clock pulse provided it is edge triggered.

Ramachandran P.R

• Apr 30th, 2006

Ans is for positive edge triggerd flipflop out put:0 and for negative edge triggered output:1

Answer Question  Select Best Answer

smokindesi

• Oct 9th, 2006

could be anywhere in memory. You can get the address from the location in IVT (assuming this subroutine is not chained) based on service number (i.e Interrupt no)location of address (i.e pointer)is available at 4*(interrupt serviced)

vikas s kulkarni

• Aug 3rd, 2005

It is stored in interrupt vector table

Answer Question  Select Best Answer

sumanyaram

 Profile Answers by sumanyaram Questions by sumanyaram

• Dec 5th, 2006

5 flipflops r enough to divide the frequency by 32

S

• Aug 15th, 2006

32=2^5 => 5 bit longNumber divisible is 2*5=10 bit longQuotient & Remainder both are 5 bit eachso total 25 flip-flops at least (+ may be some other auxilliary register also)

Answer Question  Select Best Answer

sumanyaram

 Profile Answers by sumanyaram Questions by sumanyaram

• Dec 5th, 2006

Praveen is right,1101 is not a valid BCD number........

Danny John

• Aug 8th, 2006

Praveen is right. we are supposed to do exactly what he did. For verification convert them to decimal that is 9 + 4 =13 that is in BCD it is 0001 0011.

Answer Question  Select Best Answer

sumanyaram

 Profile Answers by sumanyaram Questions by sumanyaram

• Dec 5th, 2006

Sorry it is +23 onesX(2^127) and -23onesX(2^127)i bit for sign so only 23 bits

sumanyaram

 Profile Answers by sumanyaram Questions by sumanyaram

• Dec 5th, 2006

mantissa=24 bits , exponent=8 bitsfirst consider the exponent,range is -128 to +127second consider the mantissa , max is all onesso ans is: 24 ones X (2^127) is the max positivenumber -2...

Answer Question  Select Best Answer

swatias

 Profile Answers by swatias Questions by swatias

• Jan 11th, 2007

Mantisa  range = + 2 ^ 23 to - 2^23Exponent range = 127 to - 126so total number range will be +2^23 * 10^127 to - 2^23*10^-126

santos

• Aug 30th, 2006

-126

Answer Question  Select Best Answer

rajeev kumar

• Feb 7th, 2007

Locality of reference means refering a particular area of memory while allocating variables.Whenever we allocate variables they are stored in a particular area this phenomenon is called locality of reference.

vijay

• Dec 14th, 2006

Definition of: locality of reference Also known as "locality in space" and "spatial locality," it refers to the fact that most instructions in a program are in routines that are executed over and over...

Answer Question  Select Best Answer

Give the pinout & functional block diagram with the parts and controls.

yogeshforever

 Profile Answers by yogeshforever Questions by yogeshforever

• Aug 4th, 2007

DCE stannds for data communication end. In compouter? world? a modem is a DCE device.DTE stands for data terminal equipment. It serves as the originators and receptors of the digital communication.For more information refer to the "Introduction to Microprocessor" by "Shridhar and Ghosh"

bashwin.87

 Profile Answers by bashwin.87 Questions by bashwin.87

• Feb 12th, 2007

U can think DCE as a modem & DTE as a system

Answer Question  Select Best Answer

reddy

• Oct 31st, 2007

The use of capacitor circuits instead of logical gates as in static RAMs demand the refreshing circuits.The charging and discharging of capacitors while storing bits could cause errors.

Answer Question  Select Best Answer

Arun Segaran

• Nov 2nd, 2007

Not?many?synthesis?tools?are?available?to?synthesize?a?asynchronous?design?at?RTL?

swatias

 Profile Answers by swatias Questions by swatias

• Jan 11th, 2007

To avoid race effects and deadlock effect, synchronous circuits are used

Answer Question  Select Best Answer

How much time does a serial link of 64 Kbps take to transmit a picture with 540 pixels.

japan_dave88

 Profile Answers by japan_dave88 Questions by japan_dave88

• Aug 20th, 2009

I would say that it also depends on length of the link as suppose Two devices named A and B are located 1000 kilometer far and we have link of 64kbps. Than when A will start sending first bit of ...

shreekanthss

 Profile Answers by shreekanthss Questions by shreekanthss

• Feb 2nd, 2009

Suppose a pixel is represented by 8 bits. Then total size=540*8=4320bitsIt takes 4320/64000=0.0675 seconds

Answer Question  Select Best Answer

muthumlk

 Profile Answers by muthumlk Questions by muthumlk

• Aug 4th, 2010

For an SR latch, if S is in ON state, the latch is set. So the o/p is 1 and the latch is in ON state.

Gopi

• Jun 1st, 2005

Latch state is in high state( ouput Q = 1).

Answer Question  Select Best Answer