-
Describe a 3-way TCP/IP Handshake?
RAJA
- Apr 25th, 2006
The communication b/w two tcp host are established by using 3-way handshaking.these are request , acknowldgement ,and data transfer.transmitting host sent request to receiving host,receiving host sent ACK to senting host and then data is transfer from source to destination.
shaik_bavajan
- Apr 15th, 2006
Three way TCP/Ip handshake means, while communicating with other system.3 procedure will done those are request,reply and aknoledgement.
-
-
What does CIDR stand for?
-
What is a Bridge? When is it used? How is a bridge configured? What are the software and hardware components of a bridge?
vmshenoy
- Jan 8th, 2007
Bridge are data link layer devices! Store and forward devices.Many organisation have multiple LANs.LANs can b connected by devices called Bridges.
Navaneethan
- Jul 25th, 2006
Bridge which is used to segment the network. So it reduces the network traffic between the two segments.
-
What is the Network Time Protocol?
Why is it used
sreekanth396
- Aug 9th, 2009
Network time protocol is a protocol for synchronizing the clock of computer system over?packet switched, variable latency data networks .NTP uses UDP protocol number 123 as it's? transport layer.
Tanveer
- Mar 21st, 2006
Network Time Protocol, a protocol to exchange and synchronize time on computer networks
-
What is RIP (Routing Information Protocol)?
It is a simple protocol used to exchange information between the routers.
monami85
- Jun 3rd, 2008
Rip is a true distance vector routing algorithm.Every 30seconds rip sends it complete routing table out to all active interfaces.RIP uses hop count to determine the best way to reach a remote network,...
RameshKumar Kaliamoorthi
- Dec 5th, 2006
RIP is one of the most enduring of all routing protocols. RIP is also one of the more easily confused protocols because a variety of RIP-like routing protocols proliferated, some of which even used th...
-
What is BGP (Border Gateway Protocol)?
It is a protocol used to advertise the set of networks that can be reached with in an autonomous system. BGP enables this information to be shared with the autonomous system. This is newer than EGP (Exterior Gateway Protocol).
-
What is subnet?
A generic term for section of a large networks usually separated by a bridge or router.
Crsna Suneel
- May 19th, 2009
In topology and related areas of mathematics, a subnet is a generalization of the concept of subsequence to the case of nets. The definition is not completely straightforward, but is designed to allow...
-
What is the range of addresses in the classes of internet addresses?
Class A 0.0.0.0 - 127.255.255.255Class B 128.0.0.0 - 191.255.255.255Class C 192.0.0.0 - 223.255.255.255Class D 224.0.0.0 - 239.255.255.255Class E 240.0.0.0 - 247.255.255.255
-
What are the data units at different layers of the TCP / IP protocol suite?
The data unit created at the application layer is called a message, at the transport layer the data unit created is called either a segment or an user datagram, at the network layer the data unit created is called the datagram, at the data link layer the datagram is encapsulated in to a frame and finally transmitted as signals along the transmission media.
-
What is Protocol Data Unit?
The data unit in the LLC level is called the protocol data unit (PDU). The PDU contains of four fields a destination service access point (DSAP), a source service access point (SSAP), a control field and an information field. DSAP, SSAP are addresses used by the LLC to identify the protocol stacks on the receiving and sending machines that are generating and using the data. The control field specifies...
adityawalia9
- Jun 15th, 2010
LAN uses different ways of communicating. In some ways (like ETHERNET) data link layer is divided into two parts MAC and LLC (Logical Link Control).At LLC the data is known as Protocol Data Unit....
monami85
- May 23rd, 2008
each layer or the osi model , formats the data that it receives , the package of data moves through the layers is called protocol data unit. the protocol dat unit n...
-
What is point-to-point protocol?
A communications protocol used to connect computers to remote networking services including Internet service providers.
Piyush Verma
- Nov 3rd, 2010
It is a data link layer protocol that is used to provide direct link between nodes. It can provide connection authentication, transmission encryption or privacy and compression.
adityawalia9
- Jun 15th, 2010
Point-to-Point Protocol is a data link protocol. It is a byte oriented protocol (data will be treated a byte).It does not have any flow control (and error control is also limited). It is used wh...
-
Difference between the communication and transmission.Transmission is a physical movement of information and concern issues like bit polarity, synchronisation, clock etc.Communication means the meaning full exchange of information between two communication media.
siyanat
- May 4th, 2008
Transmission means sending some information or data from 1place to another but only transmit where as at receiving end we can not b sure whether it is received or not.communication means two way communication for eg if u send any info or data that must be received at the receiving end
reehan10
- Mar 29th, 2008
Communication device is the terminal or the endpoint wishing to communicate....eg:computer...communication media is the medium used for the communication eg:cable.hope the answer to your question
-
What is Active Directory? How does it work?
tosine
- Oct 18th, 2009
Active directory is a directory that enables organisation to create a scalable, secured and manageable infrastructure for user and resource management and to support directory-enabled application. It...
giri_adepu
- Jun 2nd, 2008
In windows 2000 and 2003 environment ads is a power full sercice ,active directory mainly used for maintaing and promotion of entire company into centralized network administration .it means domine evironmnet
-
What is layer-3 switch?
Thomas Whitten
- Jun 27th, 2011
A layer 2 switch provides connectivity but doesn't act upon the packets at all.? These switches are often found in small offices, your home or on the very edge of a LAN to provide Internet or client/...
sony
- Sep 15th, 2006
A layer 2 switch provides switchingA Layer 3 switch provides Switching as well as Routing
-
What is Private IP? Give an example?
Thomas Whitten
- Jun 27th, 2011
In the WAN topology, a network is divided usually by the firewall into the 'outside' or public IP addresses and the 'inside' or private IP addresses.? The is done because public IP addresses (provide...
kirankumar.ray
- Jul 16th, 2008
The address which can't be routed through public (internet) are private ip addressesand it is scheam of saving public addressex:in class A range is10.0.0.0 to 10.255.255.255
-
What is ipv6 ? how many octects is it ?
Thomas Whitten
- Jun 27th, 2011
IPv6 is basically the response to the fact that the world is/was running out of public ip addresses.? The best example of stupidity leading to the problem is universities handing out public IP addres...
addagalla
- Aug 5th, 2008
Ipv6 means Internet Protocol Version 6. It is the latest version. It has 16 octates.It is in Hexadecimal format.
-
What is the difference between collision domain and broadcast domain?
radhesham
- Jun 21st, 2011
Collision is intersection of two or more data at a particular point which results in Loss of data.
Broadcasting is sending data or information to every node, ports in a network
kapil
- Feb 16th, 2007
Broadcast domain is the logical address scheme in which a user can acess any other networking address without any routing devicebut in collision domain that is the combination of the single segment and multiple segments through repeter
-
What is the subnet mask of class a,b,c,d,e.and what is the minimum and maximum number of connections in class a,b,c,d,e
netsolver
- Jul 5th, 2008
N - networkH - HostClass A - 0nnnnnnn hhhhhhhh hhhhhhhh hhhhhhhh 126 Class As exist (0 and 127 are reserved) 16,777,214 hosts on each Class A Class B - 10nnnnnn nnnnnnnn hhhhhhhh hhhhhhhh First two bi...
-
What is difference between layer 2 and layer 3 switch ?how much bandwidth support by V.35 and RS 232 cable What is difference between V.35 and RS 232 Cable
xuyuan
- Aug 4th, 2008
Layer 2 switch forward or filter frames, layer 3 switch (router)?use logical addressing and provide packet switching. Router also provide packet filtering by using acess list and when connect two or ...
Computer Networks Interview Questions
Ans