you have three boxes, one has a resistor, second has a capacitor, and the third has an inductor. Find what is in each box, using a battery, a switch and a lamp. You can build any circuit you want, to figure out which box have a resistor, and which one has the inductor, etc. How can you solve that?

chandramvs

 Profile Answers by chandramvs Questions by chandramvs

• Jan 3rd, 2016

Connect the battery, switch, lamp and the box in series and observe what happens, 1) If the lamp glows with constant brightness then the box has resistor. 2) If the lamp initially is dark and finall...

abdelmonsef

• Jan 2nd, 2016

A battery is DC, so when connecting the battery and the capacitor and the lamp in series, the lamp will not be on (as the capacitor is open circuit in DC system) and when connecting the battery and th...

Answer Question  Select Best Answer

How does Slip Power Recovery System work? How to capture supply for recovery? Is it any possibility to design model of slip power recovery system drive?

Santosh

• Jan 10th, 2016

Of course, there are different methods to recover the power wasted in rotor and that is done by using Scherbius Drive or Kramers Drive where the rotor terminals are connected to a rectifier and again...

Answer Question  Select Best Answer

What is meant by distributed winding and concentrated winding?

karthik

• Jan 20th, 2016

Concentrated and Distributed wiring definitions

Ravikumar Eta

• Jan 10th, 2016

In concentrated type winding, all the winding turns are wound together in series to form one multi coil.

In distributed type winding, all the winding turns are arranged in several full pitch or fractional pitch.

Answer Question  Select Best Answer

How can we chose transformer star to delta or delta to star connection? What condition is suitable for star connection? What condition is suitable for delta transformer?

mohammed

• Jan 18th, 2016

If we want to distribute to customers we use star connection but if we want to trasmit power we use delta connection

pdp

• Jan 13th, 2016

Delta star connection generates 73.2% more than dd and yy connection because star side requires less insulation than delta side in normal condition..we can put extra insuation to generate high voltage...

Answer Question  Select Best Answer

How can we make wattmeter to measure reactive power?

Amol takate

• Jan 27th, 2016

For calculation of the reactive power in 3 phase connected load procedure is to connect the current coil of single phase wattmeter in any phase series with the load and connect the pressure coil acros...

Answer Question  Select Best Answer

mani babu amballa

• Mar 5th, 2016

When the charging coil is disturbed suddenly, it will produce large amount of voltage

shubham

• Aug 31st, 2015

Choke work like transformer and its major components which is connected Across its inductor Stores current like caps

Answer Question  Select Best Answer

When alternator is over exited, the power factor will be
a. Lagging
b. Leading
c. Zero

Dipti Ranjan

• Mar 7th, 2016

Pf is lagging because A.R is demagnetizing.

pradeep1987

 Profile Answers by pradeep1987 Questions by pradeep1987

• Jan 31st, 2016

It is lagging. When the alternator runs at lagging power factor, the armature reaction demagnetize the main field flux. To compensate the extra magnetic field required so that the alternator is Overexcited

Answer Question  Select Best Answer

What percentage of system overhead will not result in poor performance for user programs?

>10%

>20%

GANESAMOORTHY

• Mar 28th, 2016

>20%

Avinash

• Mar 1st, 2016

>20%

Answer Question  Select Best Answer

What are the advantages & dis-advantages of Harmonics in Power System?

Qaphelani Sgcino

• Apr 2nd, 2016

Disturbances in the communication networks and telephone lines.

Kevin

• Mar 27th, 2016

Disadvantages of Harmonics: Harmonics degrades the performance of power system. Some of the disadvantages of harmonics in the power distributed network are listed below: The harmonics flowing in the...

Answer Question  Select Best Answer

What is the main difference between Transformer based UPS and Transformer less UPS and its operation?

Dheeraj Rai

• May 22nd, 2016

Transformer Based UPS Transformers in general are used for number application, the most obvious one is to stepping up or down the voltage. In UPS application they are also used: To create galvan...

Answer Question  Select Best Answer

A capacitor, resistor and inductor are connected in series as well as in parallel also. Is energy storing in those three elements are same? Explain

How to measure the cross-sectional area of a cable which is 1000 sq. mm.?

Heaven

• May 24th, 2016

3.14 x radius of cable^2

KHURAM

• Dec 10th, 2015

A=pi*r^2

Answer Question  Select Best Answer

Neutral is connected to Earth at the source to ground, the unbalanced current in the electrical network mainly in distribution system, What happens if we connect neutral to earth at load side DB?

ashutosh singh

• May 24th, 2016

What is MD & MTTR?

ali raza

• May 21st, 2016

No because when unbalance current flow through neutral short circuit occurs at that point where neutral grounded

Answer Question  Select Best Answer

What are the technical reasons for Soaking Test in Transformer and Switch Gear?

ali raza

• May 26th, 2016

I think the transformers are soaked with normal operating voltage level as testing with HV of the transformer insulation, winding at site is impractical as well not economical. Besides soaking allows ...

Answer Question  Select Best Answer

Explain How to Start a Induction Motor?

Viral p. patel

• May 28th, 2016

When we give the supply to starter winding. The alternating flux will be produce. That flux link with rotor winding through core. Then the current will be produced in rotor winding. The rotor winding ...

Answer Question  Select Best Answer

What are the elements in electrical engineering?

Josue

• May 30th, 2016

Resistors, Capacitors and Inductors

Answer Question  Select Best Answer

chanchal

• Jun 5th, 2016

Earthing is inside of earth with any conductive material and grounding is on top of the earth for machines (grounding can be with high ohms but earthing must be with 0.1 ohms)

harsha vardhan

• May 2nd, 2016

In my case both are similar

Answer Question  Select Best Answer

How to calculate the NGR resistance to connect in alternator / transformer. I mean to say thumb rule of NGR against MW capacity of alternator / transformer.

Aadil

• Jul 1st, 2016

NGR or Neutral Grounding Resistors are used to limit the ground fault current to a safe value in the event of earth fault. A NGR limits the earth fault current to a value which will be sufficient to operate protective relays and prevent unwanted fault damage.

Answer Question  Select Best Answer

What is standard height of P, R & S towers used in 132KV transmission lines?

Why 660v is use in place of 440v in some big KW motor?

A Rudrendra

• Jul 14th, 2016

It is the secondary standard voltage level in LT side and by using this voltage we can reduce the motor rated current.

Answer Question  Select Best Answer