-
How do you share a printer
MotoRooter
- Jul 27th, 2008
This is how I share a printer on a the LAN You can print from every PC on your network to one printer. To share a printer with the other PCs in your home you need to configure the PC to which the prin...
-
What is the routed protocols & routing protocols?
xuyuan
- Aug 4th, 2008
A routing protocol is used by router to dynamically find all the networks in the? internetwork and to ensure that all routers have the same routing table. Basically routing protocol determines the pa...
-
Encoding and Modulation
What is difference between encoding and modulation?..? please give me detail of encoding and modulation ?
rrsain
- Jul 29th, 2008
Encoding is assigning binary codes according to algorithm, but modulation is changing the properties of one signal(value) according to properties of another signal.
-
Printer Driver Replication
What is Printer driver replication and mapping?
-
Ping Death Packet
What is ping to death packet?What is the size of ping to death packet?/
manishtripathi
- Sep 20th, 2008
POD (Ping of Death) is a type of attack at computer in a network that involves sending of a larger size malicious ping to a computer. A ping is normally 64 bytes in size.Many computers can not handle ...
-
Default Subnet Mask for IPV6
What is the default subnet mask for IPV6?
ramzpriya
- Oct 29th, 2008
There are 3 address types in v6 - Unicast, anycast, and multicast. Unicast addresses identify a single network device, anycast and multicast addresses identify a group of network devices. IPv6 address...
-
WAP Gateway
What is the function of a WAP gateway ? Discuss WAP protocols.
goutham431
- Nov 13th, 2009
Implementation of the WAP stack Converting protocols Converting markup languages Compiling WMLScript programs Encoding WML into a binary bitstream Providing access control Caching Domain name resolution services (DNS) Security features
-
Cable Length
Why do we have a minimum and maximum cable length requirement
badariprasad
- Jun 5th, 2009
The min and max cable length is required because the signals can travel effectively without loosing their strength to that extent you can increase the cable length apart from preferred by using the repeaters after the length so that the signals will be boosted again.
-
TCP IP Integration
TCP is reliable in communication whereas IP is Non-reliable. Why it is integrated into one and given as TCP/IP protocol?
sudhavijay
- Jun 17th, 2009
Reliability not achieved at lower layers shall be implemented at the higher layers and more importantly each Layer in TCP/IP protocol suite is responsible for some network operations. IP though unrel...
-
Token Ring Segment
You need to connect a Token Ring segment to an Ethernet segment. Would you use a router, a brouter , or a bridge ?
-
Configure two DHCP Servers
How to configure two DHCP Servers using 2 swithces with 1 DSL. Keep in mind we cannot use any other additional equipment.
naveenbhatiya2007
- Jan 27th, 2011
You configure what is known as Network Address Translation (NAT) on the router. This then translates the IP address of the server, which is likely to be a 10.x.x.x or 192.168.x.x address, to be the IP...
-
What services does the internet layer provide?
Sandhya.Kishan
- Apr 19th, 2012
The internet layer packs data into data packets known as IP datagrams, which contain source and destination address information that is used to forward the datagrams between hosts and across networks....
-
Mail server communication issue for all users in a LAN
All the users in a LAN have trouble communicating with the mail server. As a Network Engineer, what are the troubleshooting steps to be followed?
-
-
Printer and NIC
how to check printer registry ? and whats the need to check printer registry waht its use?
-
What are the possible ways of data exchange?
(i) Simplex (ii) Half-duplex (iii) Full-duplex.
shridhar
- Apr 21st, 2006
Hi,Simplex ,Half Duplex , Full Duplex , Fiber Connectivit (Very Fast) Shridhra
ankitsays9
- Jan 15th, 2006
There are three possible ways of data exchange. These are:1. Simplex: in this, data is transmitted in one direction only. this means one end will always be a transmitter and the other end will always ...
-
What is subnet?
A generic term for section of a large networks usually separated by a bridge or router.
Crsna Suneel
- May 19th, 2009
In topology and related areas of mathematics, a subnet is a generalization of the concept of subsequence to the case of nets. The definition is not completely straightforward, but is designed to allow...
-
What is terminal emulation, in which layer it comes?
Telnet is also called as terminal emulation. It belongs to application layer.
Rajnish
- Apr 30th, 2012
What is terminal server and how to work in a terminal server.
Sandhya.Kishan
- Apr 19th, 2012
Terminal emulation is the ability to make one computer terminal appear like some other terminal. Terminal emulation is used to give the users the ability to log on and get direct access to legacy pro...
-
What is BGP (Border Gateway Protocol)?
It is a protocol used to advertise the set of networks that can be reached with in an autonomous system. BGP enables this information to be shared with the autonomous system. This is newer than EGP (Exterior Gateway Protocol).
-
Can we use static and dynamic routing in one network?
shridhar76
- Mar 27th, 2006
This is depend upon clients need, in broadband connection today there r static ip is mostly provided by Service provider for better result , in Dynamic routing the congession is very less.shridhar
Kalyan Raghavan
- Feb 4th, 2006
As Saurabh said; we can use static and Dynamic Routing in one network. However Dyanmic Routing is used to have the best path no matter what the status of the physical links.All routing protocols have ...
Computer Networks Interview Questions
Ans